Home / Lithophane night light
Free · runs in your browser

Lithophane Night Light Maker

Turn a photo into a backlit panel for a night light. Size it to your light, set the thickness, and print it in white filament.

Make a lithophane panel for a night light free in your browser: set the width in mm to fit your base, thickness about 0.8 mm (light) to 3 mm (dark), shape, frame and curve, then download the STL. Print upright in white filament at 100 percent infill. It makes the panel only, not the base or light holder.

Drop an image to make it 3D
PNG, JPG, WebP, SVG or iPhone HEIC · choose a file
Free · runs in your browser · nothing is uploaded
Try:
Files stay on your deviceNo sign-up for free toolsSTL · 3MF · STEP · OBJ · GLBWatertight, slicer-ready output

In short: A lithophane night light is a thin printed panel of white plastic that shows a photo when an LED shines through it from behind.

MeshShift makes the panel: drop in a photo, set the width in millimetres to fit your light, choose a thickness from about 0.8 mm for the brightest areas to about 3 mm for the darkest, pick a rectangle, rounded, circle or heart shape, add a frame, and download the STL for free. It runs in your browser, so the photo is not uploaded. You can also curve the panel up to 180 degrees. The tool does not print the lamp base or the light holder; you slot the panel into a night-light base you already have, or print a base separately. Print the panel upright in white PLA at 100 percent infill.

How to use the Lithophane Night Light Maker

  1. Measure the opening of your night light base or lamp.
  2. Drop a photo into the tool and set the width in mm.
  3. Set thinnest 0.8 mm and thickest about 3 mm, then choose the shape and frame.
  4. Download the STL and print it upright in white filament.
Starting settings for a night-light panel, Checked November 2026
SettingStart withWhy
WidthA little under your base opening, in mmSo the panel slides in
Thinnest (light areas)0.8 mmLets the light through
Thickest (dark areas)About 3 mmKeeps shadows dark
Frame2 to 4 mmStrengthens the edges
ShapeRectangle, rounded, circle or heartMatches the window
Curve0° for a flat slot, up to 180° for an arcOptional
Filament and infillWhite PLA, 100 percentEven glow
Layer height0.12 mmSmoother gradients
LightWarm white LEDPLA softens at roughly 55 to 60 °C

Sizing the panel to your light

Start from the light, not the photo. Measure the slot or opening in millimetres and set the panel width a fraction smaller so it slides in, or add the frame to make a lip that rests on the base. Height follows from the photo's proportions, so crop the photo first if you need a specific shape. A square crop fits a round or square night-light window; a portrait crop suits most plug-in bases.

The frame slider (up to 8 mm) adds a border around the picture. A 2 to 4 mm frame makes the thin edges much stronger and gives you something to hold when you slot the panel in.

Thickness: the setting that decides how it looks

A lithophane works because thin plastic lets more light through. Light areas of the photo become thin and dark areas become thick. The common range is 0.8 mm at the thinnest to 3 mm at the thickest. A thinner minimum makes highlights brighter, a thicker maximum makes shadows darker. If the picture looks washed out when lit, raise the maximum a little; if it looks too dark, lower it.

Photos with strong contrast and a clear subject, such as a face or a pet against a plain background, work best. Dark, muddy photos give a flat result whatever the thickness.

Print settings and the light source

Use white filament, 100 percent infill and a fine layer height; the tool suggests 0.12 mm. Print it standing up, the way the file is exported. Coloured filament tints the image, and a low infill leaves a visible pattern.

Use an LED, ideally a warm white one. PLA softens at around 55 to 60 degrees Celsius, so keep the panel away from hot bulbs, and leave a few millimetres of air between the LED and the plastic.

What the tool can and cannot do for a night light

Shapes: rectangle, rounded rectangle, circle or oval, and heart. Form: flat, or curved from 0 to 180 degrees. Extras: a frame and an optional keyring hole, which can double as a hanging point. Export: STL and 3MF are free; finer detail comes with any AI pack.

It does not generate a lamp base, a light-holder slot or a lid, and the curve bends along one axis only, so spheres, vases and full cylinders are out of scope. The tool turns the panel upright for printing, but it does not print a stand. Bring your own base, or model one in your CAD tool, then check that the panel width matches.

Frequently asked questions

How thick should a lithophane night light be?

About 0.8 mm at the thinnest areas and 3 mm at the thickest is a good start. Print in white filament at 100 percent infill. Adjust the maximum up if the lit picture looks washed out.

What size is a lithophane night light panel?

It depends on your base. Measure the opening in millimetres and set the panel width in the tool slightly smaller. The height follows the photo's proportions, so crop the photo to the shape you need.

What light should I use behind a lithophane?

A warm white LED is the usual choice. Avoid hot incandescent bulbs, because PLA softens at roughly 55 to 60 degrees Celsius. Leave a small gap between the light and the panel.

Does MeshShift make the night light base too?

No. The tool makes the lithophane panel, with an optional frame, curve and keyring hole. It does not generate a base or light holder, so use a base you already have or print a separate one.