Curved Lithophane Maker
Wrap a photo around an arc of up to 180 degrees. Set the width, the thickness range and the frame, and download an STL.
Make a curved lithophane free in your browser: bend a photo panel from 0 to 180 degrees, set thickness from about 0.8 mm to 3 mm, choose rectangle, circle or heart, add a frame and download the STL. The image keeps its full width along the arc. The photo is not uploaded. It makes the panel only, not a lamp base.
In short: A curved lithophane is a photo panel printed as an arc instead of a flat plate, so it stands up by itself and the light from behind spreads across the picture. MeshShift's curved lithophane maker builds one from any photo in your browser.
Turn the Curve slider from 0 to 180 degrees: the image keeps its full width along the arc, so nothing is stretched, and at 100 mm wide a 90 degree bend gives a radius of about 64 mm. Set the thinnest part to about 0.8 mm and the thickest to about 3 mm, choose rectangle, rounded, circle or heart, add an optional frame, and download the STL for free. The photo never leaves your device. The model comes out standing on its arc, ready to slice in white filament at 100 percent infill.
How to use the Curved Lithophane Maker
- Drop a photo with good contrast into the tool.
- Set the Curve slider (90 degrees is a good first try) and the width in mm.
- Set thinnest 0.8 mm and thickest about 3 mm, then pick a shape and a frame.
- Download the STL and print it upright in white filament.
| Curve | Radius | Straight-line width | Depth of the arc |
|---|---|---|---|
| 45° | 127 mm | 97 mm | 10 mm |
| 90° | 64 mm | 90 mm | 19 mm |
| 135° | 42 mm | 78 mm | 26 mm |
| 180° (half cylinder) | 32 mm | 64 mm | 32 mm |
How the curve is built
The tool first makes a normal lithophane: dark parts of the photo become thick, light parts become thin, so more light shines through the bright areas. Then it bends that panel around a vertical axis. The arc length equals the width you chose, so a 100 mm wide panel stays 100 mm along its curved surface. The radius follows from the angle: radius equals width divided by the angle in radians.
The bend is applied after the shape and the frame are built, so a heart, a circle or a framed rectangle all curve as one piece. The finished model is rotated so the arc stands on the build plate with the top of the photo pointing up, which is how a lithophane should be printed.
Choosing the angle
A small curve (45 to 60 degrees) looks almost flat and gives the panel a slight stance. Around 90 degrees the panel stands firmly and the light spreads nicely across the picture. Near 180 degrees you get a half cylinder, which wraps around a bulb or LED strip but hides part of the picture when seen from the front. The table lists the geometry for a 100 mm wide panel; values scale in proportion for other widths.
If the panel will go around a specific light, measure the light's width and pick the angle whose radius is a little larger than that.
Thickness and print settings
Start with 0.8 mm for the thinnest (lightest) areas and 3 mm for the thickest. A thinner minimum makes highlights glow brighter but can look patchy if your nozzle or layers are coarse. The tool offers the thinnest from 0.4 to 2 mm and the thickest from 1.5 to 6 mm.
Print in white PLA at 100 percent infill and a fine layer height (0.12 mm is the figure the tool suggests), standing upright as exported. Coloured filament changes the picture, because the colour is what the light carries through. An optional frame of 2 to 4 mm makes the edges sturdier; the frame slider goes to 8 mm.
What a curved lithophane here does not include
The tool makes the panel only. It does not add a lamp base, a light holder or a lid, and it bends along one axis, so it does not make a full cylinder, a sphere or a vase in one piece. If you want a closed lamp, print two half-cylinders at 180 degrees and join them, or fit the panel into a base you already have. The STL is free at the standard detail setting; 3MF export is free too; finer detail comes with any AI pack.
For a flat panel, use the regular lithophane maker. For a night light with a specific base, see the lithophane night light page.
Frequently asked questions
How do I make a curved lithophane?
Drop a photo into the curved lithophane maker, set the Curve slider to the bend you want (90 degrees is a good start), choose the width in millimetres and the thickness range, and download the STL. It runs in your browser, so the photo is not uploaded.
How far can the lithophane curve?
The slider goes from 0 to 180 degrees. At 180 degrees the panel is a half cylinder. A full 360 degree cylinder is not supported in one piece; print two halves instead.
What thickness should a curved lithophane be?
About 0.8 mm at the thinnest and 3 mm at the thickest is a solid starting point. Thinner highlights glow more, thicker shadows stay darker. Print in white filament at 100 percent infill.
Does a curved lithophane stand up without a stand?
The model is exported standing on its arc, and a curved footprint is wider than the thin edge of a flat panel, so it stands more steadily. A large panel with a tight curve can still tip, so test with a small print and add a base if needed.



